Description
P216 Series Condenser Fan Speed Controller - transducer-input, single-phase fan speed control with selectable pressure ranges, heatpump and reverse modes, and master/slave operation.
These controllers are designed for speed variation of single phase motors, especially for fan speed control on air cooled condensers. Head pressure control of a refrigeration system, through speed variation of the fan on an air-cooled condenser, results in optimum performance throughout the year.
Using a pressure transducer as the input device to the fan speed controller gives the most direct and fastest response to pressure variations in the refrigerant system. The controller varies the supply voltage to the motor from 45% to at least 95% over the proportional band using the phase cutting principle. If the pressure drops below the adjusted setpoint minus the proportional band, the output to the motor is zero volt or the adjusted min. speed setting. This provides speed variation of permanent split capacitor or shaded pole motors which do not draw more than 12 A (rms) full load current.
The controller used for dual pressure input varies the fan speed by directly sensing the pressure changes of two separate refrigerant circuits. The setpoint of each pressure transducer can be separately adjusted. The controller selects the input with the greatest cooling demand to control the fan speed. The transducers can be used in non-corrosive refrigerant systems.
Features
* The new benchmark in standard FSC
* Easy to install and easy to operate
* Output range 0.5 to 12 Amp (1 phase)
* Input 0-10 VDC
* Including 0-50 bar pressure transducer P499VCS-405C
* Heatpump mode
* Reverse operation mode
* Master / slave mode
* Fixed pressure ranges for direct replacement (P215)
* Setpoint and min speed potmeters
Operation (OEM)
A DIP switch is used to select one of 4 different pressure ranges; switch positions 1, 2 and 3 determine the range of the setpoint potentiometer. One potentiometer manually adjusts the setpoint and a second adjusts the minimum speed. A green LED indicates that power is applied. Two 3-position screw terminal blocks connect the 50 bar transducers, and a 3-position screw terminal block selects HP or Reverse modes - contacts between HP and C run the fan at full speed, and contacts between REV and C increase the fan speed as pressure decreases. In master mode the P216 operates in combination with the P499VCS-405C pressure transmitter as a stand-alone unit; in slave mode the P216 is controlled by an external 0-10 V or 0-5 V signal. Operate the P216 only in combination with one or two P499VCS-405C pressure transmitters.
This product code is named in the OEM P216 technical specification table (P216EEA-2K / P216EEA-101C), so the electrical and pressure data below are OEM-documented values. The -2K / -101C product type is the dual-transducer variant of the P216EEA controller. Note that the OEM bulletin lists the transducer as included - confirm whether the P499VCS-405C transducers ship with this product code or must be ordered separately.
Specifications
* Brand / Manufacturer: Johnson Controls / PENN
* Model / Part Number: P216EEA-101C
* Type: P216 Series Condenser Fan Speed Controller (single-phase)
* Pressure Input: Dual transducer input (P216EEA-2K / -101C product type) - with two transducers the controller always references the one sensing the highest pressure and selects the input with the greatest cooling demand
* Power Supply (OEM): 208 to 240 VAC, 50/60 Hz
* Pressure Ranges (OEM, DIP-switch selectable): Adjustable 4 to 10 bar setpoint (prop band fixed at 2.0 bar); 8 to 14 bar (2.5 bar); 14 to 24 bar (4.0 bar); 22 to 42 bar (5.0 bar)
* Pressure Transducer (OEM): P499VCS-405C, 0-50 bar range
* Input Signal (OEM): 0 to 10 VDC
* Control Action (OEM): Direct or reverse mode
* Maximum Current (OEM): 12 A (8 A if mounted in direct sunlight, or ambient limited to 40°C)
* Minimum Current (OEM): 0.5 A
* Protection Class (OEM): IP54
* Ambient Operating Conditions (OEM): -40 to 60°C
* Storage Temperature (OEM): -40 to 85°C
* Dimensions (OEM): 159 x 177 x 70 mm (H x W x D)
* Weight (OEM): 1 kg
* MTTR (OEM): 20 years
* Wiring (OEM): Wires between controller and fan motor must not exceed 15 m (50 ft); line-voltage wires 3.31 mm² (12 AWG) or smaller; low-voltage wires less than 30 m (100 ft); copper conductors only
* Conformity (OEM): EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC
* Reference Documentation: P216 Condenser Fan Speed Controller Product Bulletin, PB_P216
* Condition: New
Johnson Controls / Johnson Controls
P216EEA-101C / P216EEA101C
P216EEA-101C / P216EEA101C
Warranty Information
B2E Surplus includes a 90-day return window on all orders. If you have any issues with your order, automated returns can be opened by following the instructions located here: https://www.b2esurplus.com/returns/
Subject to the exclusions described below, all B2E Surplus products (“Products”) are warranted to be free from defects in materials and workmanship under normal use and service. Unless otherwise set forth in a quotation or agreed to by B2E Surplus in writing, standard Products are warranted for 90 days from the date of delivery to the buyer.
EXCLUSIVE REMEDY. In the event that B2E Surplus determines that a Product contains a defect in materials or workmanship, then B2E Surplus, in its sole discretion, will (a) repair the Product, (b) replace the Product, or (c) refund the purchase price of the Product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE REMEDY OF REPAIR, REPLACEMENT OR REFUND IS BUYER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. IN NO EVENT SHALL B2E SURPLUS’ LIABILITY UNDER THIS WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT GIVING RISE TO THE WARRANTY CLAIM. All Products which are repaired or replaced shall be warranted only for the unexpired portion of the original warranty period.
EXCLUSIONS. This warranty does not cover (a) any failures which are not attributable to defects in materials or workmanship, including without limitation, failures caused by accidents, inadequate maintenance, misuse, unauthorized modifications or repairs, improper storage, and normal wear and tear, (b) any consumable parts or accessories, such as cutter blades, nut splitter chisels, punches, dies, chains, wedges, and strands, that are designed to wear over time or through use of the Product, or (c) electronics, motors, batteries, and engines, as these items are warranted by their manufacturer.
WARRANTY RETURNS. No Products shall be returned without prior authorization from B2E Surplus. Buyer shall prepay all shipping charges for the return of Products to B2E Surplus’ designated service location.
LIMITATION OF LIABILITY. IN NO EVENT SHALL B2E SURPLUS BE LIABLE FOR ANY INCIDENTAL DAMAGES, CONSEQUENTIAL DAMAGES, SPECIAL DAMAGES, INDIRECT DAMAGES, LOSS OF PROFITS, LOSS OF REVENUES, OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. B2E SURPLUS' LIABILITY FOR DAMAGES ARISING OUT OF OR RELATED TO ANY ORDER IS LIMITED TO THE ORDER PRICE FOR THE SPECIFIC PRODUCT THAT GIVES RISE TO THE CLAIM. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THESE LIMITATIONS AND EXCLUSIONS SHALL APPLY REGARDLESS OF WHETHER LIABILITY ARISES FROM BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE), BY OPERATION OR LAW, OR OTHERWISE.
B2E Surplus LLC is a non-authorized stocking distributor for this brand. We are also known as a ""surplus"", ""discount"", ""liquidator"", or ""gray market"" supplier. We are not a factory-authorized distributor of this product. The Original Manufacturer’s Warranty does not apply. B2E Surplus LLC's standard 90-day warranty will apply. B2E Surplus LLC makes no representations as to your ability or right to download, re-distribute, or otherwise obtain products from this manufacturer, its distributors, or any other source. It is your obligation to comply with the terms of any rules obtaining or installing this product.
Our complete warranty statement page is located here: https://www.b2esurplus.com/warranty/
Our complete return policy page is located here: https://www.b2esurplus.com/returns/
