Description
P-5217 Static Pressure Transmitter - low volume pneumatic transmitter that converts a static pressure differential referenced to atmosphere into a proportional 3 to 15 PSIG output signal.
The P-5217 Static Pressure Transmitter is a low volume instrument which measures a particular differential pressure as referenced to atmosphere and converts the measurement into a proportional 3 to 15 PSIG (21 to 105 kPa) output signal.
The P-5217, with external restrictor, is used to measure a static pressure differential; for example, end of duct run or fan discharge segments of an air distribution system. A signal, proportional to the measured static differential, is transmitted to an indicator, recorder, or receiver-controller.
Operation (OEM)
There are three connections on the P-5217: high input, low input, and supply/output. The supply/output connection is a barbed fitting for 5/32 or 1/4 in. O.D. polytubing. Both the high and the low input connections are barbed fittings for 3/8 in. O.D. polytubing. For certain applications it may be preferable to use 1/2 in. O.D. polytubing on the low sensing line.
The low input connection must be referenced to atmosphere. When static pressure at the high input connection is higher than the reference static pressure, a proportional signal is transmitted from the supply/output port in accordance with the differential established between the low and high input ports. As the differential increases, an internal mechanism proportionally increases the output signal. When the differential reaches the maximum of its range, the output from the supply/output port will be 15 PSIG (105 kPa). When the differential is at its minimum, the output will be 3 PSIG (21 kPa).
Mounting and Installation (OEM)
* May be mounted in any position using the mounting bracket provided; vertical mounting is preferred since the instrument is factory calibrated in this plane. If horizontal mounting is required, the instrument must be recalibrated
* Locate the transmitter near the source of the atmospheric low reference pressure to keep the low input connection line as short as possible
* Because the low pressure reference line is connected to the control line, magnehelic type gages should not be teed into it - they may be teed into the high line only
* A field-supplied .007 in. restrictor must be installed at the transmitter; 20 PSIG (140 kPa) is applied to the supply/output port during calibration, with zero and span adjustments provided
* If the P-5217 fails to operate within its specifications, unit replacement is required; field repairs cannot be made (check the restrictor before assuming the transmitter is inoperable)
Applications
* Duct static pressure transmission at end-of-run or fan discharge locations
* Static pressure signal to pneumatic indicators, recorders and receiver-controllers
* Building or space static pressure referenced to atmosphere
RANGE NOT OEM-VERIFIED FOR THIS DASH NUMBER. The OEM bulletin lists the available ranges in a specifications table that could not be extracted from the retrieved document, so the sensing span of this model is not confirmed from an OEM source. No range figure could be found for the bare P-5217 code in any source; the OEM bulletin covers the series and the dash number identifies the span. Read the range from the transmitter label before fitting or reselling.
Specifications
* Brand / Manufacturer: Johnson Controls
* Model / Part Number: P-5217
* Type: P-5217 Static Pressure Transmitter (pneumatic)
* Sensing Range: Not documented for this code - read from the transmitter label
* Output Signal (OEM): Proportional 3 to 15 PSIG (21 to 105 kPa)
* Connections (OEM): Supply/output barbed fitting for 5/32 or 1/4 in. O.D. polytubing; high and low input barbed fittings for 3/8 in. O.D. polytubing (1/2 in. O.D. may be preferred on the low sensing line)
* Reference (OEM): Low input connection must be referenced to atmosphere
* Required Accessory (OEM): Field-supplied .007 in. restrictor, installed at the transmitter
* Calibration (OEM): Factory calibrated in the vertical plane; zero adjustment screw and span adjustment pin valve provided
* Repair (OEM): Field repairs cannot be made - replace the unit
* Reference Documentation: P-5217 Static Pressure Transmitter Product Bulletin, Code No. LIT-7171225 (Part No. 24-4635-3, Rev. A)
* Condition: New. Johnson Controls. Johnson Controls. P-5217.
Warranty Information
B2E Surplus includes a 90-day return window on all orders. If you have any issues with your order, automated returns can be opened by following the instructions located here: https://www.b2esurplus.com/returns/
Subject to the exclusions described below, all B2E Surplus products (“Products”) are warranted to be free from defects in materials and workmanship under normal use and service. Unless otherwise set forth in a quotation or agreed to by B2E Surplus in writing, standard Products are warranted for 90 days from the date of delivery to the buyer.
EXCLUSIVE REMEDY. In the event that B2E Surplus determines that a Product contains a defect in materials or workmanship, then B2E Surplus, in its sole discretion, will (a) repair the Product, (b) replace the Product, or (c) refund the purchase price of the Product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE REMEDY OF REPAIR, REPLACEMENT OR REFUND IS BUYER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. IN NO EVENT SHALL B2E SURPLUS’ LIABILITY UNDER THIS WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT GIVING RISE TO THE WARRANTY CLAIM. All Products which are repaired or replaced shall be warranted only for the unexpired portion of the original warranty period.
EXCLUSIONS. This warranty does not cover (a) any failures which are not attributable to defects in materials or workmanship, including without limitation, failures caused by accidents, inadequate maintenance, misuse, unauthorized modifications or repairs, improper storage, and normal wear and tear, (b) any consumable parts or accessories, such as cutter blades, nut splitter chisels, punches, dies, chains, wedges, and strands, that are designed to wear over time or through use of the Product, or (c) electronics, motors, batteries, and engines, as these items are warranted by their manufacturer.
WARRANTY RETURNS. No Products shall be returned without prior authorization from B2E Surplus. Buyer shall prepay all shipping charges for the return of Products to B2E Surplus’ designated service location.
LIMITATION OF LIABILITY. IN NO EVENT SHALL B2E SURPLUS BE LIABLE FOR ANY INCIDENTAL DAMAGES, CONSEQUENTIAL DAMAGES, SPECIAL DAMAGES, INDIRECT DAMAGES, LOSS OF PROFITS, LOSS OF REVENUES, OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. B2E SURPLUS' LIABILITY FOR DAMAGES ARISING OUT OF OR RELATED TO ANY ORDER IS LIMITED TO THE ORDER PRICE FOR THE SPECIFIC PRODUCT THAT GIVES RISE TO THE CLAIM. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THESE LIMITATIONS AND EXCLUSIONS SHALL APPLY REGARDLESS OF WHETHER LIABILITY ARISES FROM BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE), BY OPERATION OR LAW, OR OTHERWISE.
B2E Surplus LLC is a non-authorized stocking distributor for this brand. We are also known as a ""surplus"", ""discount"", ""liquidator"", or ""gray market"" supplier. We are not a factory-authorized distributor of this product. The Original Manufacturer’s Warranty does not apply. B2E Surplus LLC's standard 90-day warranty will apply. B2E Surplus LLC makes no representations as to your ability or right to download, re-distribute, or otherwise obtain products from this manufacturer, its distributors, or any other source. It is your obligation to comply with the terms of any rules obtaining or installing this product.
Our complete warranty statement page is located here: https://www.b2esurplus.com/warranty/
Our complete return policy page is located here: https://www.b2esurplus.com/returns/
