Description
The Johnson Controls M9132-AGA-2 is a direct-mount electric non-spring-return actuator - 280 lb·in (32 N·m), AC/DC 24 V, for on/off (two-position) and floating control, with no auxiliary switches. This is the largest single actuator in the M91xx range.
Per Johnson Controls' M9132 Series selection chart, the M9132-AGA-2 is the on/off & floating model with no auxiliary switches, rated 280 lb-in (32 Nm), 115 - 205 sec timing, AC 24 V 50/60 Hz, DC 24 V.
Published specification:
* Torque: 280 lb·in (32 N·m)
* Control input: on/off (two-position) or floating
* Timing: 115 to 205 seconds
* Supply: AC 24 V 50/60 Hz or DC 24 V
* Power consumption: 6.5 VA
* Rotation range: 0 to 90°, mechanically adjustable in 5° increments
* Shaft: round up to 3/4 in. (20 mm) diameter, or square up to 5/8 in. (16 mm)
* Auxiliary switches: none - see the M9132-AGC-2
* Ambient: -4 to 122°F (-20 to 50°C), 0 to 90% RH
Top of the range on torque, and the slowest stroke because of it. At 280 lb·in this is double the M9116 and a third more than the M9124, which is what you want on a large, high-velocity or tightly-sealed damper. The trade is travel time: 115 to 205 seconds against 70-115 on the M9116. If the sequence of operation calls for a damper to be proven open within a fixed window, check that number before you specify.
This is not a modulating actuator. An A model is driven by switched contacts: energise one input and it drives open, energise the other and it drives closed, energise neither and it stops where it is. That last behaviour is what makes it a floating (tri-state) actuator - a controller can inch it to any intermediate position by pulsing the inputs, with no analogue signal involved. It will not follow a 0-10 V or 4-20 mA command. If your controller has an analogue output, you want the M9132-GGA-2.
There is also no position feedback on this code. If you need proof of position, the M9132-AGC-2 adds two SPDT switched contacts.
In Johnson Controls' words, these are bidirectional actuators that "do not require a damper linkage, and are easily installed on a damper with a round shaft up to a 3/4 in. (20 mm) in diameter or a square shaft up to 5/8 in. (16 mm)." The series also has electronic stall detection, which the manufacturer describes as ensuring "higher reliability by deactivating the actuator motor when a stall condition is detected."
Setup features: jumper-selectable rotation direction and a manual gear release, so direction and position can be set on the damper without power and without re-wiring. Master/slave operation allows synchronised control for two actuators, and the housing is designed to be stacked for tandem applications.
Tandem: Johnson Controls rates two -AGx, -GGx or -HGx models in tandem at twice the torque - 560 lb·in (64 N·m), the highest figure published for this range. Tandem hardware differs by model, so ask us to confirm the correct kit for the AGx before you order.
Valve option: mounts to VG1000 Series ball valves and VG7000 Series globe valves using an M9000-5xx Valve Linkage Kit.
Non-spring return: holds its last position on loss of power. For outdoor air dampers in cold climates Johnson Controls recommends a spring-return actuator instead.
* Brand / Manufacturer: Johnson Controls
* Model / Part Number: M9132-AGA-2
* Series: M9132 Series electric non-spring-return actuators
* Torque: 280 lb·in (32 N·m)
* Control: On/off (two-position) and floating
* Feedback: None
* Auxiliary switches: None - see the M9132-AGC-2
* Timing: 115 to 205 seconds
* Supply: AC/DC 24 V
* Spring return: No - holds last position
* Condition: New
We hold the M9102 through M9132 Series from 18 to 280 lb·in, plus brackets, linkages, jackshaft kits, tandem hardware and weather shields. Tell us the damper or valve, the torque and the control signal and we will match it from stock.
Johnson Controls / Johnson Controls
M9132-AGA-2 / M9132AGA2
M9132-AGA-2 / M9132AGA2
Warranty Information
B2E Surplus includes a 90-day return window on all orders. If you have any issues with your order, automated returns can be opened by following the instructions located here: https://www.b2esurplus.com/returns/
Subject to the exclusions described below, all B2E Surplus products (“Products”) are warranted to be free from defects in materials and workmanship under normal use and service. Unless otherwise set forth in a quotation or agreed to by B2E Surplus in writing, standard Products are warranted for 90 days from the date of delivery to the buyer.
EXCLUSIVE REMEDY. In the event that B2E Surplus determines that a Product contains a defect in materials or workmanship, then B2E Surplus, in its sole discretion, will (a) repair the Product, (b) replace the Product, or (c) refund the purchase price of the Product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE REMEDY OF REPAIR, REPLACEMENT OR REFUND IS BUYER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. IN NO EVENT SHALL B2E SURPLUS’ LIABILITY UNDER THIS WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT GIVING RISE TO THE WARRANTY CLAIM. All Products which are repaired or replaced shall be warranted only for the unexpired portion of the original warranty period.
EXCLUSIONS. This warranty does not cover (a) any failures which are not attributable to defects in materials or workmanship, including without limitation, failures caused by accidents, inadequate maintenance, misuse, unauthorized modifications or repairs, improper storage, and normal wear and tear, (b) any consumable parts or accessories, such as cutter blades, nut splitter chisels, punches, dies, chains, wedges, and strands, that are designed to wear over time or through use of the Product, or (c) electronics, motors, batteries, and engines, as these items are warranted by their manufacturer.
WARRANTY RETURNS. No Products shall be returned without prior authorization from B2E Surplus. Buyer shall prepay all shipping charges for the return of Products to B2E Surplus’ designated service location.
LIMITATION OF LIABILITY. IN NO EVENT SHALL B2E SURPLUS BE LIABLE FOR ANY INCIDENTAL DAMAGES, CONSEQUENTIAL DAMAGES, SPECIAL DAMAGES, INDIRECT DAMAGES, LOSS OF PROFITS, LOSS OF REVENUES, OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. B2E SURPLUS' LIABILITY FOR DAMAGES ARISING OUT OF OR RELATED TO ANY ORDER IS LIMITED TO THE ORDER PRICE FOR THE SPECIFIC PRODUCT THAT GIVES RISE TO THE CLAIM. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THESE LIMITATIONS AND EXCLUSIONS SHALL APPLY REGARDLESS OF WHETHER LIABILITY ARISES FROM BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE), BY OPERATION OR LAW, OR OTHERWISE.
B2E Surplus LLC is a non-authorized stocking distributor for this brand. We are also known as a ""surplus"", ""discount"", ""liquidator"", or ""gray market"" supplier. We are not a factory-authorized distributor of this product. The Original Manufacturer’s Warranty does not apply. B2E Surplus LLC's standard 90-day warranty will apply. B2E Surplus LLC makes no representations as to your ability or right to download, re-distribute, or otherwise obtain products from this manufacturer, its distributors, or any other source. It is your obligation to comply with the terms of any rules obtaining or installing this product.
Our complete warranty statement page is located here: https://www.b2esurplus.com/warranty/
Our complete return policy page is located here: https://www.b2esurplus.com/returns/
